DumpTorrent NSE8_812 dumps & Fortinet Network Security Expert Sure Practice with 107 Questions

New NSE8_812 Exam Questions| Real NSE8_812 Dumps

NEW QUESTION # 48
Refer to the exhibits, which show a network topology and VPN configuration.

A network administrator has been tasked with modifying the existing dial-up IPsec VPN infrastructure to detect the path quality to the remote endpoints.
After applying the configuration shown in the configuration exhibit, the VPN clients can still connect and access the protected 172.16.205.0/24 network, but no SLA information shows up for the client tunnels when issuing the diagnose sys link-monitor tunnel all command on the FortiGate CLI.
What is wrong with the configuration?

• A. It is necessary to use the IKEv2 protocol in this situation.
• B. The admin needs to disable the mode-cfg setting.
• C. SLA link monitoring does not work with the net-device setting.
• D. IPsec Phase1 Interface has to be configured in IPsec main mode.

Answer: C

NEW QUESTION # 49
Refer to The exhibit showing a FortiEDR configuration.

Based on the exhibit, which statement is correct?

• A. If an unresolved file rule is triggered, by default the file is logged but not blocked.
• B. The presence of a cryptolocker malware at rest on the filesystem will be detected by the Ransomware Prevention security policy.
• C. FortiEDR Collector will not collect OS Metadata.
• D. If a malicious file is executed and attempts to establish a connection it will generate duplicate events.

Answer: A

NEW QUESTION # 50
Refer to the exhibit.

To facilitate a large-scale deployment of SD-WAN/ADVPN with FortiGate devices, you are tasked with configuring the FortiGate devices to support injecting of IKE routes on the ADVPN shortcut tunnels.
Which three commands must be added or changed to the FortiGate spoke config vpn ipsec phasei-interface options referenced in the exhibit for the VPN interface to enable this capability? (Choose three.)

• A. set add-route enable
• B. set net-device disable
• C. set mode-cfg enable
• D. set mode-cfg-allow-client-selector enable
• E. set ike-version 1

Answer: A,B,D

Explanation:
A is correct because net-device disable prevents the VPN interface from being added to the routing table as a connected route. This allows IKE routes to be injected instead. D is correct because add-route enable enables IKE route injection on the VPN interface. E is correct because mode-cfg-allow-client-selector enable allows the VPN interface to accept IKE routes from any peer that matches the phase 1 configuration. Reference: https://docs.fortinet.com/document/fortigate/7.0.1/administration-guide/490352/advpn https://docs.fortinet.com/document/fortigate/7.0.1/administration-guide/490352/advpn-configuration

NEW QUESTION # 51
An automation stitch was configured using an incoming webhook as the trigger named 'my_incoming_webhook'. The action is configured to execute the CLI Script shown:

• A.
• B.
• C.
• D.

Answer: B

Explanation:
To execute the CLI script shown using an incoming webhook as the trigger, the correct syntax for the curl command is: curl -X POST -H "Content-Type: application/json" -d '{"trigger_name":"my_incoming_webhook"}' https://fortisoar.example.com/api/v1/trigger This command will send a POST request to the FortiSOAR API endpoint with the trigger name and the content type as JSON. The FortiSOAR API will then execute the automation stitch that matches the trigger name and run the CLI script on the FortiGate device. Reference: https://docs.fortinet.com/document/fortisoar/7.0.0/administration-guide/103440/automation-stitches https://docs.fortinet.com/document/fortisoar/7.0.0/administration-guide/103441/incoming-webhook

NEW QUESTION # 52
Refer to the exhibits.

A customer is trying to restore a VPN connection configured on a FortiGate. Exhibits show output during a troubleshooting session when the VPN was working and the current baseline VPN configuration.

Which configuration parameters will restore VPN connectivity based on the diagnostic output?

• A.
• B.
• C.
• D.

Answer: D

NEW QUESTION # 53
Refer to the exhibit.

To facilitate a large-scale deployment of SD-WAN/ADVPN with FortiGate devices, you are tasked with configuring the FortiGate devices to support injecting of IKE routes on the ADVPN shortcut tunnels.
Which three commands must be added or changed to the FortiGate spoke config vpn ipsec phasei-interface options referenced in the exhibit for the VPN interface to enable this capability? (Choose three.)

• A. set add-route enable
• B. set mode-cfg enable
• C. set net-device disable
• D. set mode-cfg-allow-client-selector enable
• E. set ike-version 1

Answer: A,B,D

Explanation:
* B must be set to enable mode-cfg, which is required for injecting IKE routes on the ADVPN shortcut tunnels.
* D must be set to enable add-route, which is the command that actually injects the IKE routes.
* E must be set to enable mode-cfg-allow-client-selector, which allows custom phase 2 selectors to be configured.
The other options are incorrect. Option A is incorrect because net-device disable is not required for injecting IKE routes on the ADVPN shortcut tunnels. Option C is incorrect because IKE version 1 is not supported for ADVPN.
References:
* Phase 2 selectors and ADVPN shortcut tunnels | FortiGate / FortiOS 7.2.0
* Configuring SD-WAN/ADVPN with FortiGate | FortiGate / FortiOS 7.2.0

NEW QUESTION # 54
An administrator has configured a FortiGate device to authenticate SSL VPN users using digital certificates.
A FortiAuthenticator is the certificate authority (CA) and the Online Certificate Status Protocol (OCSP) server.
Part of the FortiGate configuration is shown below:

Based on this configuration, which two statements are true? (Choose two.)

• A. If the OCSP server is unreachable, authentication will succeed if the certificate matches the CA.
• B. OCSP certificate responses are never cached by the FortiGate.
• C. OCSP checks will always go to the configured FortiAuthenticator
• D. The OCSP check of the certificate can be combined with a certificate revocation list.

Answer: C,D

Explanation:
References:
Configuring SSL VPN authentication using digital certificates | FortiGate / FortiOS 7.2.0 - Fortinet Document Library Online Certificate Status Protocol (OCSP) | FortiGate / FortiOS 7.2.0 - Fortinet Document Library Certificate Revocation Lists (CRLs) | FortiGate / FortiOS 7.2.0 - Fortinet Document Library

NEW QUESTION # 55
Refer to the exhibit, which shows a VPN topology.

The device IP 10.1.100.40 downloads a file from the FTP server IP 192.168.4.50 Referring to the exhibit, what will be the traffic flow behavior if ADVPN is configured in this environment?

• A. All the session traffic will pass through the Hub
• B. Spoke1 will establish an ADVPN shortcut to Spoke2
• C. ADVPN is not supported when spokes are behind NAT
• D. The TCP port 21 must be allowed on the NAT Device2

Answer: B

Explanation:
D is correct because Spoke1 will establish an ADVPN shortcut to Spoke2 when it detects that there is a demand for traffic between them. This is explained in the Fortinet Community article on Technical Tip:
Fortinet Auto Discovery VPN (ADVPN) under Summary - ADVPN sequence of events. References:
https://community.fortinet.com/t5/FortiGate/Technical-Tip-Fortinet-Auto-Discovery-VPN-ADVPN/ta-p
/195698

NEW QUESTION # 56
Refer to the exhibits.


A customer is looking for a solution to authenticate the clients connected to a hardware switch interface of a FortiGate 400E.
Referring to the exhibits, which two conditions allow authentication to the client devices before assigning an IP address? (Choose two.)

• A. Ports 3 and 4 can be part of different switch interfaces.
• B. Devices connected directly to ports 3 and 4 can perform 802 1X authentication.
• C. FortiGate devices with NP6 and hardware switch interfaces cannot support 802.1X authentication.
• D. Client devices must have 802 1X authentication enabled

Answer: B,D

Explanation:
The customer wants to deploy a solution to authenticate the clients connected to a hardware switch interface of a FortiGate 400E device. A hardware switch interface is an interface that combines multiple physical interfaces into one logical interface, allowing them to act as a singleswitch with one IP address and one set of security policies. The customer wants to use 802.1X authentication for this solution, which is a standard protocol for port-based network access control (PNAC) that authenticates clients based on their credentials before granting them access to network resources. One condition that allows authentication to the client devices before assigning an IP address is that devices connected directly to ports 3 and 4 can perform 802.1X authentication. This is because ports 3 and 4 are part of the hardware switch interface named "lan", which has an IP address of 10.10.10.254/24 and an inbound SSL inspection profile named "ssl-inspection". The inbound SSL inspection profile enables the FortiGate device to intercept and inspect SSL/TLS traffic from clients before forwarding it to servers, which allows it to apply security policies and features such as antivirus, web filtering, application control, etc. However, before performing SSL inspection, the FortiGate device needs to authenticate the clients using 802.1X authentication, which requires the clients to send their credentials (such as username and password) to the FortiGate device over a secure EAP (Extensible Authentication Protocol) channel. The FortiGate device then verifies the credentials with an authentication server (such as RADIUS or LDAP) and grants or denies access to the clients based on the authentication result. Therefore, devices connected directly to ports 3 and 4 can perform 802.1X authentication before assigning an IP address.
Another condition that allows authentication to the client devices before assigning an IP address is that client devices must have 802.1X authentication enabled. This is because 802.1X authentication is a mutual process that requires both the client devices and the FortiGate device to support and enable it. The client devices must have 802.1X authentication enabled in their network settings, which allows them to initiate the authentication process when they connect to the hardware switch interface of the FortiGate device. The client devices must also have an 802.1X supplicant software installed, which is a program that runs on the client devices and handles the communication with the FortiGate device using EAP messages. The client devices must also have a trusted certificate installed, which is used to verify the identity of the FortiGate device and establish a secure EAP channel. Therefore, client devices must have 802.1X authentication enabled before assigning an IP address. References: https://docs.fortinet.com/document/fortigate/7.0.0/administration-guide/19662/hardware- switch-interfaceshttps://docs.fortinet.com/document/fortigate/7.0.0/administration-guide/19662/802-1x- authentication
https://docs.fortinet.com/document/fortigate/7.2.0/new-features/959502/support-802-1x-on-virtual-switch-for- certain-np6-platforms

NEW QUESTION # 57
Refer to the exhibit.

The exhibit shows the forensics analysis of an event detected by the FortiEDR core In this scenario, which statement is correct regarding the threat?

• A. This is an exfiltration attack and has been stopped by FortiEDR.
• B. This is an exfiltration attack and has not been stopped by FortiEDR
• C. This is a ransomware attack and has not been stopped by FortiEDR.
• D. This is a ransomware attack and has been stopped by FortiEDR

Answer: D

Explanation:
The exhibit shows the forensics analysis of an event detected by the FortiEDR core. The event graph indicates that a process named svchost.exe was launched by a malicious file named 1.exe, which was downloaded from a suspicious URL. The process then attempted to encrypt files in various folders, such as Documents, Pictures, and Desktop, which are typical targets of ransomware attacks. However, FortiEDR was able to stop the process and prevent any file encryption by applying its real-time post-execution prevention feature. Therefore, this is a ransomware attack and has been stopped by FortiEDR. Reference: https://docs.fortinet.com/document/fortiedr/6.0.0/administration-guide/733983/forensics https://www.fortinet.com/content/dam/fortinet/assets/data-sheets/fortiedr.pdf

NEW QUESTION # 58
Review the following FortiGate-6000 configuration excerpt:

Based on the configuration, which statement is correct regarding SNAT source port partitioning behavior?

• A. It statically distributes SNAT source ports to operating FPCs or FPMs
• B. It equally distributes SNAT source ports across chassis slots.
• C. It is the default SNAT configuration and preserves active sessions when an FPC or FPM goes down.
• D. It dynamically distributes SNAT source ports to operating FPCs or FPMs.

Answer: A

Explanation:
Based on the configuration, the statement that is correct regarding SNAT source port partitioning behavior is that it statically distributes SNAT source ports to operating FPCs or FPMs. This is because the nat-source-port option is set to chassis-slots, which means that the FortiGate-6000 will allocate SNAT source ports to all FPCs or FPMs that are enabled when the command is entered. If an FPC or FPM is disabled from the CLI, the SNAT source ports assigned to that FPC or FPM will not be re-allocated to the remaining FPCs or FPMs. This option preserves active sessions when an FPC or FPM goes down, but does not dynamically re-distribute SNAT source ports if an FPC or FPM is powered off. Reference: https://docs.fortinet.com/document/fortigate/7.2.5/fortigate-6000-administration-guide/81276/controlling-snat-port-partitioning-behavior

NEW QUESTION # 59
Refer to The exhibit, which shows a topology diagram.

A customer wants to use SD-WAN for traffic generated from the data center towards Branches. SD-WAN on HUB should follow the underlay condition on each Branch and the solution should be scalable for hundreds of Branches.
Which SD WAN-Rules strategy should be used?

• A. Auto based on link quality
• B. Lowest Cost SLA
• C. Manual based on route-tags
• D. Best Quality based on route-tags

Answer: D

NEW QUESTION # 60
An HA topology is using the following configuration:

Based on this configuration, how long will it take for a failover to be detected by the secondary cluster member?

• A. 300ms
• B. 600ms
• C. 200ms
• D. 100ms

Answer: C

Explanation:
The HA heartbeat interval is 100ms, and the number of lost heartbeats before a failover is detected is 2. So, it will take 2 * 100ms = 200ms for a failover to be detected by the secondary cluster member.
Reference:
FortiGate High Availability: https://docs.fortinet.com/document/fortigate/7.0.0/administration-guide/647723/link-monitoring-and-ha-failover-time

NEW QUESTION # 61
You must configure an environment with dual-homed servers connected to a pair of FortiSwitch units using an MCLAG.
Multicast traffic is expected in this environment, and you should ensure unnecessary traffic is pruned from links that do not have a multicast listener.
In which two ways must you configure the igmps-f lood-traffic and igmps-flood-report settings? (Choose two.)

• A. enable on ICL trunks
• B. enable on the ISL and FortiLink trunks
• C. disable on the ISL and FortiLink trunks
• D. disable on ICL trunks

Answer: A,C

Explanation:
https://docs.fortinet.com/document/fortiswitch/7.0.8/devices-managed-by-fortios/801194/deploying-mclag- topologies

NEW QUESTION # 62
Refer to the exhibit.

You have been tasked with replacing the managed switch Forti Switch 2 shown in the topology.
Which two actions are correct regarding the replacement process? (Choose two.)

• A. After replacing the FortiSwitch unit, the automatically created trunk name does not change
• B. After replacing the FortiSwitch unit, the automatically created trunk name changes.
• C. CLAG-ICL needs to be manually reconfigured once the new switch is connected to the FortiGate
• D. MCLAG-ICL will be automatically reconfigured once the new switch is connected to the FortiGate.

Answer: A,D

Explanation:
Based on the exhibit, the two correct actions regarding the replacement process are:
After replacing the FortiSwitch unit, the automatically created trunk name does not change. This is because the trunk name is based on the slot number and port number of the FortiGate unit that connects to the FortiSwitch unit, which remain the same after the replacement. If a different trunk name is desired, the trunk must be deleted and a new trunk will be created automatically with an updated name.
MCLAG-ICL will be automatically reconfigured once the new switch is connected to the FortiGate. This is because the MCLAG-ICL configuration is stored on the FortiGate unit and applied to the FortiSwitch unit when it is authorized. The replacement FortiSwitch unit will inherit the MCLAG-ICL configuration of the failed FortiSwitch unit after it is replaced using the replace-device command in FortiOS. Reference: https://docs.fortinet.com/document/fortiswitch/7.0.8/devices-managed-by-fortios/173284/replacing-a-managed-fortiswitch-unit

NEW QUESTION # 63
Refer to the exhibits.

You must integrate a FortiMail and FortiSandbox Enhanced Cloud solution for a customer who is concerned about the e-mails being delayed for too long.
According to the configuration shown in the exhibits, which would be an expected behavior?

• A. FortiMail will not wait for results but only for attachments that have been already submitted to the FortiSandbox in the last 60 minutes.
• B. If an attachment is sent to the FortiSandbox while the job queue is full, the e-mail might be delayed for up to 30 minutes, then e-mail will be relayed to the mail server.
• C. FortiMail will ignore the timeout value if content disarm and reconstruction (CDR) is enabled.
• D. FortiMail will relay valid e-mails to the mail server as soon as it is done with other local inspections.

Answer: D

NEW QUESTION # 64
Refer to the exhibits.


A customer is looking for a solution to authenticate the clients connected to a hardware switch interface of a FortiGate 400E.
Referring to the exhibits, which two conditions allow authentication to the client devices before assigning an IP address? (Choose two.)

• A. Ports 3 and 4 can be part of different switch interfaces.
• B. Devices connected directly to ports 3 and 4 can perform 802 1X authentication.
• C. FortiGate devices with NP6 and hardware switch interfaces cannot support 802.1X authentication.
• D. Client devices must have 802 1X authentication enabled

Answer: B,D

Explanation:
The customer wants to deploy a solution to authenticate the clients connected to a hardware switch interface of a FortiGate 400E device. A hardware switch interface is an interface that combines multiple physical interfaces into one logical interface, allowing them to act as a single switch with one IP address and one set of security policies. The customer wants to use 802.1X authentication for this solution, which is a standard protocol for port-based network access control (PNAC) that authenticates clients based on their credentials before granting them access to network resources. One condition that allows authentication to the client devices before assigning an IP address is that devices connected directly to ports 3 and 4 can perform 802.1X authentication. This is because ports 3 and 4 are part of the hardware switch interface named "lan", which has an IP address of 10.10.10.254/24 and an inbound SSL inspection profile named "ssl-inspection". The inbound SSL inspection profile enables the FortiGate device to intercept and inspect SSL/TLS traffic from clients before forwarding it to servers, which allows it to apply security policies and features such as antivirus, web filtering, application control, etc. However, before performing SSL inspection, the FortiGate device needs to authenticate the clients using 802.1X authentication, which requires the clients to send their credentials (such as username and password) to the FortiGate device over a secure EAP (Extensible Authentication Protocol) channel. The FortiGate device then verifies the credentials with an authentication server (such as RADIUS or LDAP) and grants or denies access to the clients based on the authentication result. Therefore, devices connected directly to ports 3 and 4 can perform 802.1X authentication before assigning an IP address.
Another condition that allows authentication to the client devices before assigning an IP address is that client devices must have 802.1X authentication enabled. This is because 802.1X authentication is a mutual process that requires both the client devices and the FortiGate device to support and enable it. The client devices must have 802.1X authentication enabled in their network settings, which allows them to initiate the authentication process when they connect to the hardware switch interface of the FortiGate device. The client devices must also have an 802.1X supplicant software installed, which is a program that runs on the client devices and handles the communication with the FortiGate device using EAP messages. The client devices must also have a trusted certificate installed, which is used to verify the identity of the FortiGate device and establish a secure EAP channel. Therefore, client devices must have 802.1X authentication enabled before assigning an IP address. References: https://docs.fortinet.com/document/fortigate/7.0.0/administration-guide/19662/hardware- switch-interfaces https://docs.fortinet.com/document/fortigate/7.0.0/administration-guide/19662/802-1x- authentication
https://docs.fortinet.com/document/fortigate/7.2.0/new-features/959502/support-802-1x-on-virtual-switch-for- certain-np6-platforms

NEW QUESTION # 65
A remote worker requests access to an SSH server inside the network. You deployed a ZTNA Rule to their FortiClient. You need to follow the security requirements to inspect this traffic.
Which two statements are true regarding the requirements? (Choose two.)

• A. FortiGate can perform SSH access proxy host-key validation.
• B. You need to configure a FortiClient SSL-VPN tunnel to inspect the SSH traffic.
• C. SSH traffic is tunneled between the client and the access proxy over HTTPS
• D. Traffic is discarded as ZTNA does not support SSH connection rules

Answer: A,C

Explanation:
ZTNA supports SSH connection rules that allow remote workers to access SSH servers inside the network through an HTTPS tunnel between the client and the access proxy (FortiGate). The access proxy acts as an SSH client to connect to the real SSH server on behalf of the user, and performs host-key validation to verify the identity of the server. The user can use any SSH client that supports HTTPS proxy settings, such as PuTTY or OpenSSH. Reference: https://docs.fortinet.com/document/fortigate/7.0.0/ztna-deployment/899992/configuring-ztna-rules-to-control-access

NEW QUESTION # 66
Refer to the exhibit that shows VPN debugging output.

The VPN tunnel between headquarters and the branch office is not being established.
What is causing the problem?

• A. The Phase-1 encryption algorithms are not matching.
• B. There is no matching Diffie-Hellman Group.
• C. HQ is using IKE v1 and the branch office is using with IKE v2.
• D. There is a mismatch in the ISAKMP SA lifetime.

Answer: A

NEW QUESTION # 67
You have configured a Site-to-Site IPsec VPN tunnel between a FortiGate and a third-party device but notice that one of the error counters on the tunnel interface keeps increasing.

Which two configuration options can resolve this problem? (Choose two.)

• A. Enable DF-bit honoring in the global settings.
• B. Enable Forward Error Correction (FEC) on the VPN interface for egress traffic.
• C. Adjust the MTU of the physical interface to which the IPsec tunnel is bound.
• D. Adjust the MTU of the IPsec interface.

Answer: A,D

NEW QUESTION # 68
Refer to the exhibit.

A customer wants to automate the creation and configuration of FortiGate VM instances in a VMware vCenter environment using Terraform. They have the creation part working with the code shown in the exhibit.
Which code snippet will allow Terraform to automatically connect to a newly deployed FortiGate if its IP was dynamically assigned by VMware NSX-T?

• A.
• B.
• C.
• D.

Answer: D

NEW QUESTION # 69
Review the VPN configuration shown in the exhibit.

What is the Forward Error Correction behavior if the SD-WAN network traffic download is 500 Mbps and has 8% of packet loss in the environment?

• A. 2 redundant packet for every 8 base packets
• B. 1 redundant packet for every 10 base packets
• C. 3 redundant packet for every 5 base packets
• D. 3 redundant packet for every 9 base packets

Answer: B

Explanation:
The FEC configuration in the exhibit specifies that if the packet loss is greater than 10%, then the FEC mapping will be 8 base packets and 2 redundant packets. The download bandwidth of 500 Mbps is not greater than 950 Mbps, so the FEC mapping is not overridden by the bandwidth setting. Therefore, the FEC behavior will be 2 redundant packets for every 8 base packets.
Here is the explanation of the FEC mappings in the exhibit:
* Packet loss greater than 10%: 8 base packets and 2 redundant packets.
* Upload bandwidth greater than 950 Mbps: 9 base packets and 3 redundant packets.
The mappings are matched from top to bottom, so the first mapping that matches the conditions will be used.
In this case, the first mapping matches because the packet loss is greater than 10%. Therefore, the FEC behavior will be 2 redundant packets for every 8 base packets.
Reference: https://docs.fortinet.com/document/fortigate/7.0.0/new-features/169010/adaptive-forward-error- correction-7-0-2

NEW QUESTION # 70
A customer's cybersecurity department needs to implement security for the traffic between two VPCs in AWS, but these belong to different departments within the company. The company uses a single region for all their VPCs.
Which two actions will achieve this requirement while keeping separate management of each department's VPC? (Choose two.)

• A. Create an 1AM account for the cybersecurity department to manage both existing VPC, create a FortiGate HA Cluster on each VPC and IPSEC VPN to force traffic between the VPCs through the FortiGate clusters
• B. Create a transit VPC with a FortiGate HA cluster, connect to the other two using VPC peering, and use routing tables to force traffic through the FortiGate cluster.
• C. Create a VPC with a FortiGate auto-scaling group with a Transit Gateway attached to the three VPC to force routing through the FortiGate cluster
• D. Migrate all the instances to the same VPC and create 1AM accounts for each department, then implement a new subnet for a FortiGate auto-scaling group and use routing tables to force the traffic through the FortiGate cluster.

Answer: B,C

Explanation:
To implement security for the traffic between two VPCs in AWS, while keeping separate management of each department's VPC, two possible actions are:
* Create a transit VPC with a FortiGate HA cluster, connect to the other two using VPC peering, and use routing tables to force traffic through the FortiGate cluster. This option allows the cybersecurity department to manage the transit VPC and apply security policies on the FortiGate cluster, while the other departments can manage their own VPCs and instances. The VPC peering connections enable direct communication between the VPCs without using public IPs or gateways. The routing tables can be configured to direct all inter-VPC traffic to the transit VPC.
* Create a VPC with a FortiGate auto-scaling group with a Transit Gateway attached to the three VPCs to force routing through the FortiGate cluster. This option also allows the cybersecurity department to manage the security VPC and apply security policies on the FortiGate cluster, while the other departments can manage their own VPCs and instances. The Transit Gateway acts as a network hub that connects multiple VPCs and on-premises networks. The routing tables can be configured to direct all inter-VPC traffic to the security VPC. References: https://docs.fortinet.com/document/fortigate-public- cloud/7.2.0/aws-administration-guide/506140/connecting-a-local-fortigate-to-an-aws-vpc-vpn
https://docs.fortinet.com/document/fortigate-public-cloud/7.0.0/sd-wan-architecture-for-enterprise/166334/sd-wan-configuration

NEW QUESTION # 71
......

NSE8_812 Braindumps – NSE8_812 Questions to Get Better Grades: https://pass4sure.dumptorrent.com/NSE8_812-braindumps-torrent.html